CBAA FLEX
CAP 65/90-E

Asphalts modified by elastomeric polymers

It is an elastomeric polymer-modified asphalt cement, and it may also contain other additives, if necessary, with a minimum softening point of 65ºC and 90% of elastic recovery. CAP 65/90-E has superior performance characteristics when compared to conventional asphalt and polymer-modified asphalts 55/75-E and 60/85-E.

CBAA FLEX <br/> CAP 65/90-E

Technical Specifications

Descrição

Description

arrow

CBAA FLEX CAP 65/90-E It is an asphalt cement modified with elastomeric polymer and other additives that, under special process conditions, present performance characteristics, such as:

  • Reduced thermal sensitivity – High softening point;
  • Resistance to repeated thermal and mechanical stresses – Elasticity;
  • Aging resistance.
Usos

Uses

arrow

CBAA FLEX CAP 65/90-E presents superior performance and durability in paving services, reducing maintenance costs and levels of road accidents, being an effective solution in terms of cost / benefit in asphalt services, such as:

  • Hot-Used Asphaltic Concrete (C.A.U.Q), for severe weather and traffic conditions on highways and urban roads;
  • Discontinuous Asphalt Coatings (C.P.A. – Friction Porous Layer / S.M.A. – Stone Matrix Asphalt), increasing the safety and durability of the coating, reducing problems on rainy days (aquaplaning / water spray);
  • Surface treatments and stress absorption membranes (S.A.M. / S.A.M.I.) increasing the adhesion and cohesion forces of the aggregate / binder pair, reducing the effects of traffic and climate on the asphalt coating.
Aplicação

Application

arrow

CBAA FLEX CAP 65/90-E it can be damaged if heated to high temperatures (above 190°C) or after repeated or prolonged reheating. It is usually delivered in the machining temperature range (160°C – 175°C), and must be unloaded in tanks free of conventional asphalt ballast (CAP – 50/70 or CAP – 30/45)

It is recommended, during storage for a period longer than 5 days, to store the product at a milder temperature than usual (between 100°C and 120°C), being recommended for short periods of storage at a maximum of 165°C. Store at room temperature if product is to be stored for long periods (20 days or more).

The temperature throughout the tank must be uniform, and the heat distribution must occur homogeneously, through the use of a recirculation pump. Never heat the product directly, but in tanks equipped with a thermal fluid coil.

Caracteristicas

Features

arrow

CBAA FLEX CAP 65/90-E is classified according to the Softening Point (minimum °C) and the Elastic Recovery (minimum %), according to ANP Resolution No. 897, of November 18, 2022 and DNIT 129/2011 – EM:

Apresentação

Presentation

arrow

CBAA FLEX CAP 65/90-E it is supplied in bulk, liquid (tons) in tank cars.

Recomendações

Recommendations

arrow

During handling, use PPE (Personal Protective Equipment). In the event of an accident, consult the Safety Data Sheet for Chemical Products (FISPQ – No. CBAA.010).

Restrições

Employment restriction

arrow

Do not perform asphalt paving services in environmental conditions with a temperature below 10°C, imminent rain during the course of the services or on surfaces with the presence of moisture.

Manuseio

Handling

arrow

CBAA FLEX CAP 65/90-E it is framed by the UN (3257) as a substance of risk 9 and subclass N.E (high temperature liquids)

As for the arrival of the product at the work site, the sample must be collected for the reception/quality tests.

Estocagem

Storage

arrow

The product must be kept in deposit (bulk), duly sealed, in lined tanks, with serpentine (thermal fluid steam) and circulation pumps.

The product in storage period (indefinite time) does not suffer degradation of its properties, as long as appropriate procedures are carried out, not being recommended overheating operations (>177°C), or maintenance of high temperature with successive reheating for prolonged period of storage .

In case of prolonged storage period, it is recommended to keep the asphalt temperature at 50°C/60°C or even room temperature, raising the temperature of the material for the asphalt mixture machining process.